Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
product
Electro Mechanical Solenoid Switch
Electro Mechanical Solenoid Switches are a type of switch that are used in applications that require remote-controlled or timed transmission line switching. These switches are very useful in operational systems and test setups where they supply a variety of switching combinations.View more Electro Mechanical Solenoid Switch
-
product
Bench top Dielectric Withstand tester
HYPOT III
RS-232 Interface available for automated controlPatented SmartGFI® functionPatented CAL-ALERT® functionComes complete with a test box for products terminated in a line cordPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in security settingsDigitally controlled arc detection systemNo load setup of trip current and output voltageElectronic ramping (up & down)Built-in adjustable continuity testInterconnection to HYAMP® III to form complete test system
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 6.97kΩ
40-251-024
The 40-251-024 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Generic RF ATE Test
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
product
Multi-Functional Board
PCI - HARPOON
PCI-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCI-Harpoon is to simulate - act as if the PCI-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCI-Harpoon can provide status and direct software control of the system.
-
product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the de...show more -
product
Motorized Force & Torque Measurement Test Stands
Mark-10 offers a wide and unique range of motorized force measurement and torque measurement test stands. Motorized stands offer a significant advantage over manual test stands by providing constant test speed. Some models can be programmed for advanced test sequences to accommodate demanding applications. All motorized test stands carry the CE mark. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 52.4kΩ
40-298-133
The 40-298-133 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Faraday Cages
LBA's EMFaraCage® faraday cages are EMI and RFI shielding boxes and RF test enclosures that bring convenience to device testing. Faraday cages are ideal for isolating critical systems in high field RF environments or wherever RF ingress or egress must be minimized. Security, production testing, biomedical research and semiconductor testing are only a few of the many areas where EMFaraCage® faraday shielded enclosures are employed. EMFaraCage® faraday cage enclosure systems are fully featured to ...show more -
product
Six-Cell Diffusion Testing System
Phoenix DB-6
The Phoenix DB-6 (six-cell diffusion block) provides an ideal platform compliant with 21 CFR Part 11 for release-rate testing of six vertical diffusion cells at once using manual sampling methods. Controlled by an advanced computerized display, the DB-6 provides uniform and precise heating and stirring of six cells. The compact footprint of the DB-6 economizes on lab bench space.
-
product
Inspector® Systems
SMOKE GENERATOR
With the Inspector® Easysmoker you are able to trace difficult leaks, indoors and outdoors. Also, for testing and certifying seperated waste water systems, airducts and other piping systems is the Easysmoker a valuable equipment tool. The Easysmoker has a short warm-up time, so that you can quickly start your analysis.
-
product
PCI EXPRESS® Protocol Solutions
PCI Express® technology is implemented broadly in systems requiringhigh-speed data transfer, such as video or graphics.Keysight's PCIe protocol solutions provide a complete PCIe 5.0 test path with a PCIe protocol analyzer and a PCIe exerciser. The integrated design boosts signal integrity and provides outstanding verstaility.Keysight's protocol solutions enable faster, more confident testing of PCIe designs, now and in the future.
-
product
Tensile/Compression/Bending/Torsion Testing Kits
With the constantly growing competitive pressure in today`s market are quality and product innovation basic requirements for any company.For this purpose TIRA is developing accurate and high quality material testing machines and testing systems which are manufactured according to the national and international standards DIN 5122, EN ISO 7500-1, GOST. With our testing machines you can carry out the static testing of metals, parts, wood, building materials, glass, plastics, fibers, composites etc.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - United Kingdom 240VAC
781630-06
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB d...show more -
product
DAS
System 470
The NEFF System 470 (S470) DAS is a complete, low cost moderate-speed DAS for use in computer-based applications. The S470 is designed primarily for computer automated data acquisition in test facilities, laboratories and industrial plants or wherever a moderate-speed DAS is required.
-
product
PXI/PXIe
As a leading provider of PXI products in test & measurement market, ADLINK has devoted its extensive field experience to the PXI platform. After more than ten years and developing more than 100 PXI products for automation and testing, and as a sponsor member of the PXI System Alliance, ADLINK continues to expand PXI and PXI Express offerings with innovative products, meeting the unique needs of high-speed and high-bandwidth applications, such as spectral monitoring and signal intelligence.
-
product
IPX3 IPX4 Rain Test System
CX-RIP3/4
Shenzhen Chuangxin Instruments Co., Ltd.
For checking the protection against water with spray nozzle of 0,4 mm bore are used to prove the degrees of protection for the second characteristic numerals 3 and 4 “Protection against Spraying Water” resp. “Protection against splashing Water”.
-
product
Socket Phone
Design for phone device test and system verify.Phone device: CPU,flash,baseband,LPDDR,power IC.etcPitch range from 0.30 to 1.27mmKey material: PEI,Peek,Torlon,PPS.etcContact with top pogo pin
-
product
OTDR
Shaanxi Aitelong Technology Co., Ltd
Is a device that tests the integrity of a fiber cable and is used for the building, certifying, maintaining, and troubleshooting fiber optic systems.
-
product
Electric Motor Testing
EPT Series
The EPT Series of testing systems are developed as open, modular solutions that provide complete product testing platforms.
-
product
System for the Analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel
SierraNet T328
The SierraNet T328 system provides for analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel data capture and protocol verification for developers & protocol test engineers in LAN, SAN, NAS and other Ethernet and Fibre Channel applications. Available with eight SFP28 FlexPorts™ for maximum configuration and utility, the SierraNet T328 includes an easy to use, customizable software interface, large capture buffers, and the most advanced T.A.P4 capture, triggering and filtering capabilities in the industry.
-
product
Microwave/RF Cable Test Assemblies, 110 GHz
Gore offers a rugged, lightweight 110 GHz test assembly that optimizes the performance of test systems while reducing the total cost of test and ownership over time. Our assemblies provide reliable electrical performance with flexure and temperature in demanding environments.
-
product
RFID Label Inspection System
Eurotech RFID FS
The Eurotech RFID FS RFID accurately rewinds rolls of RFID labels and validates their receptivity by running them through the Voyantic Tagsurance RFID inspection system. The unit allows stopping at a predetermined editing spot for the removal and replacement of the defective piece, as well as indicating defective labels by a mark printed by an inkjet system integrated with the machine. Adjustment of the closed loop tension control system can be made through adjusting the parameters on the softwa...show more -
product
PXI Precision Resistor Module 4-Channel, 2 to 102k
40-297-134
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 470Ω
40-252-114
The 40-252-114 is a programmable resistor module with 2 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Radar Echo Generation
Developing new automotive radar sensors, radar based Advanced Driver Assistance Systems (ADAS) or Autonomous Driving (AD) features have demanding challenges, during each step of the development process. Dynamic, flexible and scalable test concepts and test environments are required.
-
product
Surface Quality Measurement System
SQM-500W
SQM-500 Surface quality Measurement system is used for the surface cleanness testing and analyze of sample. SQM provide a quantitative analysis of the cleanness of the surface, which was the first announced by us. The system can be used to non-contract detect the contamination of the surface and provide an accurate result immediately. The result can provide a powerful and real data for analyze, which is the insurance for the quality.
-
product
Partial Discharge Detection System
JFD-2000
Wuhan Sangao Electrical Test Installations Limit Co.
Ease of use was the mandate to our engineering and design teams. The JFD-2000 uses the worldwide standard Windows operating system and an intuitive control and display panel to allow even inexperienced operators to learn quickly with minimal training. In addition, advanced features such as higher accuracy, auto-mated calibration, data analysis, and customized test recording, are standard. Use as much or as little as you like.
-
product
Resistive & Capacitive, Inductive AC Load Bank
RLC
Inductive & capacitive load banks are reactive only and must be used in combination with a resistive load bank to provide the desired load profile to test a power system. Reactive loads banks can provide either a leading power factor (Capacitive) or lagging power factor (Inductive).
-
product
Field Portable Wire Analyzer
Model 2635
The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.